When I try to burn using a Yamaha 6x4x16 burner, it seems to go just fine, then I get the following errors. Any suggestions/advice would be appreciated.
The scsi card is an Adaptec 2940.

Nero Version: 5.5.7.2
Recorder: <YAMAHA CRW6416S> Version: 1.0c - HA 2 TA 0 - 5.5.7.2
Adapter driver: <aic78xx> HA 2
Drive buffer : 2048kB
Bus Type : default (0) -> SCSI
CD-ROM: <TOSHIBA CD-ROM XM-5302TA>Version: 2095 - HA 0 TA 1 - 5.5.7.2
Adapter driver: <atapi> HA 0
Bus Type : default (0) -> ATAPI

=== Scsi-Device-Map ===
DiskPeripheral : SAMSUNG SV0844A atapi Port 0 ID 0 DMA: On
CdRomPeripheral : TOSHIBA CD-ROM XM-5302TA atapi Port 0 ID 1 DMA: Off
DiskPeripheral : WDC WD136AA atapi Port 1 ID 1 DMA: Off
CdRomPeripheral : YAMAHA CRW6416S 1.0c aic78xx Port 2 ID 0 DMA: ?


7:32:00 PM #15 mmc -1119 File Writer.cpp, Line 321
Track following error

7:32:00 PM #16 Text 0 File ThreadedTransfer.cpp, Line 219
all writers idle, stopping conversion

7:32:01 PM #17 Text 0 File ThreadedTransfer.cpp, Line 213
conversion idle, stopping reader

8:02:27 PM #18 CDR -201 File WriterStatus.cpp, Line 186
Invalid writestate

8:02:27 PM #19 TRANSFER -18 File WriterStatus.cpp, Line 186
Could not perform EndTrack

8:06:35 PM #20 Phase 38 File dlgbrnst.cpp, Line 1436
Burn process failed at 2x (300 KB/s)

8:06:35 PM #21 Text 0 File Scsicmd.cpp, Line 371
SCSI not using temporary buffers
20 out of 20 temporary buffers allocated

8:06:37 PM #22 SCSI -1080 File Cdrdrv.cpp, Line 1207
SCSI Exec, HA 2, TA 0, LUN 0
Status: 0x04 (0x01, SCSI_ERR)
HA-Status 0x00 (0x00, OK)
TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
Sense Key: 0x02 (KEY_NOT_READY)
Sense Code: 0x3A
Sense Qual: 0x02
CDB Data: 0x1E 0x00 0x00 0x00 0x00 0x00
Sense Data: 0x70 0x00 0x02 0x00 0x00 0x00 0x00 0x0A
0x00 0x00 0x00 0x00 0x3A 0x02

:(

"Could not perform EndTrack"

I've seen THAT before! With an old 4x HP
and NERO 5.5.x!!!!!

It sounds like an old (but very nice) burner.

I'd look for an older Nero. The 5.0.4.x series
was good. Most of the 5.5 series are bugware.

Better yet, try NTI CD Maker Pro or VOB Instant
CD/DVD.

Good Luck!

}---:)

Hi Folks, I have had some problems with Yamaha Burners in the past. The best thing to do is to check their Website and get the latest version of the "Firmware" for your burner. If your burner is not using the latest version it could be the source of the problem. After upgrading the Firmware all the problems I was having disappeared. :cool: :D