BetaONE will rise again! - Creative Soundblaster Audigy 2

Seems like Creative want to keep this as a secret :unsure:

http://ru.europe.creative.com/suppor...asp?thre=40085

This is for the Sound Blaster Live & Audigy Series Only. Not the Sound Blaster Audigy 2 Series.

Code:

Pin-Outs

Pin Name &nbsp; &nbsp; &nbsp; Description 

1 VCC &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;+5V power supply 

2 VCC &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;+5V power supply 

3 GND &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Ground 

4 AC97CLK &nbsp; &nbsp; &nbsp;24.5 MHz clock output 

5 GND &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Ground 

6 GP_SPDIFIN#2 SPDIF input signal 

7 GND &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Ground 

8 GND &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;Ground 

9 SPDIFO#3 &nbsp; &nbsp; SPDIF out Signal 

10 GPO1 &nbsp; &nbsp; &nbsp; &nbsp;General Purpose Output #1 

11 GPO2 &nbsp; &nbsp; &nbsp; &nbsp;General Purpose Output #2 

12 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

13 GPO0 &nbsp; &nbsp; &nbsp; &nbsp;General Purpose Output #0 

14 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

15 GP_ &nbsp; &nbsp; &nbsp; &nbsp; SPDIFIN1 SPDIF Input signal 

16 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

17 GPDIFO#0 &nbsp; &nbsp;SPDIF Out signal 

18 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

19 SPDIFO#1 &nbsp; &nbsp;SPDIF Out signal 

20 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

21 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

22 SPDIFO SPDIF Out signal 

23 GPI0 &nbsp; &nbsp; &nbsp; &nbsp;Digital Input (GP Input 0; Reserved) 

24 GPI1 &nbsp; &nbsp; &nbsp; &nbsp;Digital Input (GP Input 1; Reserved) 

25 OUTMIDI MIDI Output 

26 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

27 INMIDI MIDI Input 

28 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

29 KEY &nbsp; &nbsp; &nbsp; &nbsp; no pin 

30 KEY &nbsp; &nbsp; &nbsp; &nbsp; no pin 

31 ADCSDO2 &nbsp; &nbsp; I2S audio data input 

32 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

33 ADCSDO1 &nbsp; &nbsp;I2S audio data input.

34 GND &nbsp; &nbsp; &nbsp; &nbsp;Ground 

35 ADCSDO0 &nbsp; &nbsp; I2S audio data input 

36 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

37 I2SCLK I2S &nbsp;serial bit clock 

38 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground 

39 I2SFS &nbsp; &nbsp; &nbsp; Frame sync. 

40 GND &nbsp; &nbsp; &nbsp; &nbsp; Ground

But Wait ....
Could this be a sollution ?
http://www.ncix.com/forums/index.php...&overclockid=0

Quote:

For those still interested in hooking up their front audio ports (Super Lanboy/P160/Sonata) to their Audigy2 ZS (possibly Audigy2), I've been doing some research.
Despite lack of information from Creative, my Audigy2 ZS is fitted with a white 10 in-line pin connector(Intel-Standard?) at the top near the bracket(My Audigy2 does not have this although the picture on the box shows it). A similar connector can be found behind the audio ports on my P160 and a Super Lanboy I'm building for a friend.
Oddly Dell uses the same connector behind its audio ports on my daughters Dimension 8250.
Here's Antecs hook-up instructions:

Please follow these directions to make your Audio Connection.

There is an Intel standard 10-pin connector (with also 7 individual wires with individual connectors) attached to a gray wire leading from the front panel speaker and microphone connection. If your motherboard supports Intel's standard onboard audio connector, you can plug the 10-pin connector directly onto the board. For non-Intel standard audio connections, you need to plug the 7 individual connectors into the motherboard.

Instructions for non-standard audio connections.
1. Locate the internal audio connectors from your motherboard or sound card.
2. Consult your motherboard or sound card manual for the pin-out positions.
3. Microphone Power Pin: Connect the MIC connector to this pin.
4. Microphone Input Pin: Connect the MIC-BIAS connector to this pin.
5. Ground Pin: Connect the AUD GND connector to this pin.
6. Front Right Speaker Out Pin: Connect the FPOUT-R connector to this pin.
7. Front Left Speaker Out Pin: Connect the FPOUT-L connector to this pin.
8. Rear Right Speaker Out Pin: Connect the RET-R connector to this pin.
9. Rear Left Speaker Out Pin: Connect RET-L connector to this pin.
Note: Your motherboard may not support rear speakers output. In this case you do not need to connect RET-R and RET-L.

The connector is white and about 1" long. Where does one find this cable and do some Audigy 2's have this connector too?

You can see the connector on the top left of this Audigy2 OEM: http://www.ncix.com/products/index.p...560&vpn=SB0240

The white 10 pin in-line connector is Dell proprietary which I found out through Creatives Developer site. They sent me the pinouts which I have at home.
I'll post them later. They don't seem to match exactly to the Antec connectors as Antec has provision for rear speakers and
Dell has rear panel mute signalling but I'm betting it could be made to work